Interface Definition

CAM576-B2B connects to the base board through DF40C series board-to-board (B2B) connectors. The pin definitions below come from an interim version of the schematic; the materials have not been fully organized and confirmed and may change. For the complete pin definitions and multiplexing relationships, please refer to the "CAM576-B2B_V10 Schematic";
Connectors
| Connector | Model | Main Signals |
|---|---|---|
| J2 | DF40C-100DS-0.4V | Power input (TBD), control, SDMMC0, ETH0/ETH1, LCDC/EBC, GPIO |
| J3 | DF40C-100DP-0.4V | PCIe/SATA/USB3, MIPI CSI0/1/2, HDMI/eDP, USB2, audio, debug |
| J8 | DF40C-30DP-0.4V | GPIO expansion |
Only the core board part has been adapted so far; the base board is still in design and development, and the materials are still being organized and confirmed. Connector pins, interface levels, power supply capability, and connector stacking orientation may all change; the actual product and the final version of the schematic shall prevail.
Power and Control
The supply voltage, current capability, and power-up sequence of the core board have not been finalized and mainly depend on the base board design.
J2 Power and Control Pins
| Signal | Pin | Description |
|---|---|---|
| Power input | J2: 1 / 3 / 5 / 7 / 9, 2 / 4 / 6 / 8 | Supplied by the base board, voltage/current TBD |
| GND | J2: 10 ~ 17, etc. | Ground |
| VDC_EXT | J2: 23 | External power detection |
| PWRON_L | J2: 19 | Power-on signal, active low |
| RESET_L | J2: 29 | Reset signal, active low |
| PMIC_EXT_EN_OUT | J2: 31 | PMIC external enable output |
The schematic also contains power nets such as VCCA_3V3_S0, VCC_3V3_S3, and VCC_1V8_S3; whether they are exposed and their load capability are subject to the final version of the schematic and the base board design.
Debug and Boot
| Signal | Pin | Description |
|---|---|---|
| UART0_TX_M0_DEBUG | J3: 5 | Debug UART TX |
| UART0_RX_M0_DEBUG | J3: 3 | Debug UART RX |
| SARADC_IN0_BOOT | J3: 7 | BOOT button |
| SARADC_IN1_KEY/RECOVERY | J3: 9 | RECOVERY button |
| SARADC_IN3 | J3: 11 | ADC input |
| SARADC_IN4 | J3: 13 | ADC input |
| CLK_32K_IN / GPIO0_A2 | J3: 1 | 32.768kHz clock input |
The debug UART level and baud rate are subject to the firmware configuration.
Storage Interface
SDMMC0
| Signal | Pin |
|---|---|
| SDMMC0_D2 | J2: 45 |
| SDMMC0_D3 | J2: 47 |
| SDMMC0_CLK | J2: 49 |
| SDMMC0_CMD | J2: 51 |
| SDMMC0_D1 | J2: 53 |
| SDMMC0_D0 | J2: 55 |
| SDMMC0_PWREN | J2: 59 |
| SDMMC0_DETN | J2: 61 |
Supports a 4-bit SD card interface. The UFS 2.2 storage is an onboard device.
Ethernet Interface
The core board exposes ETH0 / ETH1 RGMII signals; the Ethernet PHY must be provided/determined by the base board.
| Signal | Pin |
|---|---|
| ETH1_RXD0_M0 | J2: 71 |
| ETH1_RXD1_M0 | J2: 73 |
| ETH1_RXCTL_M0 | J2: 75 |
| ETH1_RXD3_M0 | J2: 77 |
| ETH1_RXD2_M0 | J2: 79 |
| ETH1_RXCLK_M0 | J2: 81 |
| ETH1_TXD3_M0 | J2: 85 |
| ETH1_TXCLK_M0 | J2: 87 |
| ETH1_TXD2_M0 | J2: 89 |
| ETH1_TXD1_M0 | J2: 91 |
| ETH1_TXD0_M0 | J2: 93 |
| ETH1_TXCTL_M0 | J2: 95 |
| ETH1_MDC_M0 | J2: 97 |
| ETH1_MDIO_M0 | J2: 99 |
ETH0 is multiplexed onto pins such as GPIO2 / GPIO3 of J2; see the schematic for the specific multiplexing relationships.
HDMI / Display Interfaces
HDMI TX / eDP TX
The schematic includes only HDMI TX (output), with no HDMI IN.
| Signal | Pin |
|---|---|
| HDMI_TX_SBDN / EDP_TX_AUXN | J3: 79 |
| HDMI_TX_SBDP / EDP_TX_AUXP | J3: 81 |
| HDMI_TX_D3N / EDP_TX_D3N | J3: 83 |
| HDMI_TX_D3P / EDP_TX_D3P | J3: 85 |
| HDMI_TX_D0N / EDP_TX_D0N | J3: 87 |
| HDMI_TX_D0P / EDP_TX_D0P | J3: 89 |
| HDMI_TX_D1N / EDP_TX_D1N | J3: 91 |
| HDMI_TX_D1P / EDP_TX_D1P | J3: 93 |
| HDMI_TX_D2N / EDP_TX_D2N | J3: 95 |
| HDMI_TX_D2P / EDP_TX_D2P | J3: 97 |
HDMI DDC / HPD / CEC are multiplexed onto J3: 15 ~ 21.
MIPI DSI
MIPI DSI supports 4-lane output; see the schematic for the specific pins.
RGB / EBC
The RGB LCDC and EBC e-paper signals are multiplexed onto GPIO3 pins of J2 (J2: 56 ~ 100) and can be used for parallel RGB screens or e-paper.
CSI Interfaces
MIPI CSI0
| Signal | Pin |
|---|---|
| MIPI_DPHY_CSI0_RX_D0P | J3: 57 |
| MIPI_DPHY_CSI0_RX_D0N | J3: 59 |
| MIPI_DPHY_CSI0_RX_D1P | J3: 61 |
| MIPI_DPHY_CSI0_RX_D1N | J3: 63 |
| MIPI_DPHY_CSI0_RX_CLKP | J3: 65 |
| MIPI_DPHY_CSI0_RX_CLKN | J3: 67 |
| MIPI_DPHY_CSI0_RX_D2P | J3: 69 |
| MIPI_DPHY_CSI0_RX_D2N | J3: 71 |
| MIPI_DPHY_CSI0_RX_D3P | J3: 73 |
| MIPI_DPHY_CSI0_RX_D3N | J3: 75 |
MIPI CSI1 / CSI2
| Signal | Pin |
|---|---|
| CSI1_D2P / CSI2_D0P | J3: 78 |
| CSI1_D2N / CSI2_D0N | J3: 80 |
| CSI1_D3P / CSI2_D1P | J3: 82 |
| CSI1_D3N / CSI2_D1N | J3: 84 |
| CSI2_CLKP | J3: 86 |
| CSI2_CLKN | J3: 88 |
| CSI1_CLKP | J3: 90 |
| CSI1_CLKN | J3: 92 |
| CSI1_D1P | J3: 94 |
| CSI1_D1N | J3: 96 |
| CSI1_D0P | J3: 98 |
| CSI1_D0N | J3: 100 |
See the schematic for the lane multiplexing of CSI3 / CSI4.
CSI Clocks
| Signal | Pin |
|---|---|
| CAM_CLK0_OUT | J2: 73 |
| CAM_CLK1_OUT | J2: 63 |
| CAM_CLK2_OUT | J2: 65 |
USB Interfaces
USB3 OTG0 (supports DP Alt Mode)
| Signal | Pin |
|---|---|
| DP_TX_AUXP | J3: 56 |
| DP_TX_AUXN | J3: 58 |
| USB3_OTG0_SSRX1P / DP_TX_D0P | J3: 60 |
| USB3_OTG0_SSRX1N / DP_TX_D0N | J3: 62 |
| USB3_OTG0_SSTX1P / DP_TX_D1P | J3: 64 |
| USB3_OTG0_SSTX1N / DP_TX_D1N | J3: 66 |
| USB3_OTG0_SSRX2P / DP_TX_D2P | J3: 68 |
| USB3_OTG0_SSRX2N / DP_TX_D2N | J3: 70 |
| USB3_OTG0_SSTX2P / DP_TX_D3P | J3: 72 |
| USB3_OTG0_SSTX2N / DP_TX_D3N | J3: 74 |
USB2
| Signal | Pin |
|---|---|
| USB2_OTG0_VBUSDET | J3: 16 |
| USB2_OTG0_ID | J3: 18 |
| USB2_OTG0_DP | J3: 50 |
| USB2_OTG0_DM | J3: 52 |
| USB2_OTG1_DP | J3: 46 |
| USB2_OTG1_DM | J3: 48 |
See the schematic for the USB2 Host1 and USB3 Host1 pins. The VBUS, ID, protection, and connector solutions must be provided/determined by the base board.
PCIe / SATA
The connectors, reference clocks, and power solutions for PCIe / SATA must be provided/determined by the base board.
PCIe0 / SATA0
| Signal | Pin |
|---|---|
| PCIE0_REFCLKN | J3: 29 |
| PCIE0_REFCLKP | J3: 31 |
| PCIE0_RXN / SATA0_RXN | J3: 33 |
| PCIE0_RXP / SATA0_RXP | J3: 35 |
| PCIE0_TXN / SATA0_TXN | J3: 37 |
| PCIE0_TXP / SATA0_TXP | J3: 39 |
PCIe1 / SATA1 / USB3 Host1
| Signal | Pin |
|---|---|
| PCIE1_TXP / SATA1_TXP / USB3_HOST1_SSTXP | J3: 43 |
| PCIE1_TXN / SATA1_TXN / USB3_HOST1_SSTXN | J3: 45 |
| PCIE1_RXP / SATA1_RXP / USB3_HOST1_SSRXP | J3: 47 |
| PCIE1_RXN / SATA1_RXN / USB3_HOST1_SSRXN | J3: 49 |
| PCIE1_REFCLKP | J3: 51 |
| PCIE1_REFCLKN | J3: 53 |
Audio Interfaces
| Interface | Description |
|---|---|
| SAI0 | J3: 20 ~ 34, supports I2S / PCM / TDM |
| SAI1 | J3: 12 / 14, J2: 96 |
| SAI3 | Multiplexed onto J2 GPIO1 / GPIO3 pins |
| SAI4 | J3: 8 / 10 / 19 / 23 / 25 |
| PDM | Multiplexed onto J2 GPIO1 / GPIO2 pins |
| SPDIF | J3: 4 / 6, J2: 63 / 65 |
GPIO Expansion
The 100Pin of J2 and the 30Pin of J8 expose GPIO1 / GPIO2 / GPIO3 / GPIO4, which can be used for expansion such as buttons, LEDs, enables, and interrupts.
The GPIO level is determined by the VCCIO domain. The schematic indicates: VCCIO3 = 1.8V, VCCIO4 = 1.8V, VCCIO5 = 3.3V (the final levels are subject to the latest schematic). Please handle the corresponding level domains when designing the base board.
Schematic
For the complete pin definitions, multiplexing relationships, and connector stacking, please refer to the "CAM576-B2B_V10 20260718 Schematic".