Skip to main content

Upgrade Firmware

Navigation bar

Preface​

This document introduces how to flash firmware from a host computer to the memory of a Qualcomm development board via a data cable.

When upgrading, you need to select the firmware and the appropriate upgrade method based on actual requirements.

If an accident occurs during the upgrade process and the bootloader is damaged, making it impossible to re-upgrade, you can still enter MaskRom mode to repair it.

Obtaining Firmware​

  • Note: The DC2290 4G has multiple versions with different basebands/resolutions. Firmware is not interchangeable.

  • To obtain the corresponding firmware, please provide information and contact sales/technical personnel.

Installing Flashing Tools​

Download Materials​

Download and install the Qualcomm USB driver: qualcomm_usb_driver_installer_10057.4.zip

Download and install the QPST/QFIL flashing tool: qpst.win.2.7_installer_00496.2.rar

Please download the corresponding firmware for your motherboard.

Driver​

  • Please install the driver first before flashing; otherwise, the host cannot recognize the motherboard.

qualcomm_usb_driver_installer_10057.4.zip

After decompressing, open qualcomm_usb_driver_installer_10057 \ Setup.exe to install the driver.

images/QC_Flash_04.png

images/QC_Flash_05.png

Installation completed

Flashing Tool​

qpst.win.2.7_installer_00496.2.rar

Run the installer to install QPST/QFIL.

images/QC_Flash_06.png

images/QC_Flash_07.png

images/QC_Flash_08.png

images/QC_Flash_09.png

Installation completed

Starting the Upgrade​

Open the Upgrade Software​

Open Start Menu \ QPST \ QFIL upgrade software

images/QC_Flash_10.png

Opening effect


Select Firmware​

  1. Select Flat Build - Browse ...

  2. Select Fanconn_V1.1.7_DC665_TPJ_UFS_V1.1_20250312120421 \ prog_firehose_ddr.elf and click Open

images/QC_Flash_11.png

Select prog_firehose_ddr.elf

Select Partitions​

  1. Click Load XML ... again and select Fanconn_V1.1.7_DC665_TPJ_UFS_V1.1_20250312120421 \ rawprogram0_update_sparse.xml and click Open

images/QC_Flash_12.png

Select rawprogram0_update_sparse.xml

  1. In the pop-up window, select Fanconn_V1.1.7_DC665_TPJ_UFS_V1.1_20250312120421 \ patch0.xml again and click Open

images/QC_Flash_13.png

Select patch0.xml again

Entering Upgrade Mode​


Motherboard/Device Diagram​

images/QC_Flash_14.png

Wiring diagram

images/QC_Flash_15.png

If there is a casing, you can use a toothpick or similar to press the BOOT Button here.


Auto Power-On Motherboard Entering Upgrade Mode​

Auto power-on motherboards power on automatically when connected to power.

  1. Connect the USB TYPE-C data cable to the motherboard.
  2. Press and hold the Boot Button.
  3. Connect the DC12V power supply to the motherboard.
  4. Wait until it enters boot mode then release.

Manual Power-On Motherboard Entering Upgrade Mode​

For non-auto power-on motherboards, you need to manually power on after connecting the power.

  1. Connect the USB TYPE-C data cable to the motherboard.
  2. Connect the DC12V power supply to the motherboard.
  3. Press and hold the Boot Button.
  4. Press and hold the Power Button, release after entering boot mode.

Entering Loader Mode via adb shell​

When the device is in a normal state, you can also enter upgrade mode by entering the following command directly in adb:

# Check if the device is connected
adb devices
# List of devices attached

# Reboot into QDLoader mode
adb reboot edl

If you see error: closed during debugging, it means password verification is required to continue debugging.

error: closed

# Verify password
adb shell password
# Reboot into loader mode
adb reboot edl

Enter the password for normal debugging. Note: password is not the actual password. Contact technical personnel for the actual password.

Note: Passwords are not publicly released. Please contact technical personnel to obtain them.

For specific reference:

ADB Enter Flash Mode


Parameter Settings​


Select the Device to Upgrade​

When Please Select an Existing Port is displayed, click Select Port, select Qualcomm HS-USB QDLoader 9008(COM3), and click OK.

images/QC_Flash_15.png

Select Qualcomm HS-USB QDLoader 9008(COM3)


Select Device Flash Type​

According to the information on the sticker on the back of the motherboard, finally select Storage Type: - ufs.

images/QC_Flash_16.png

Select Storage Type: - ufs

Automatic Restart After Upgrade Completion​

In Configuration - FireHose Configuration - Download Configuration

Check Reset After Download

This means automatic restart after download completion

Precautions​


Clear Flash Option Erase All Before Download​

WARNING

RISK OF SYSTEM SOFTWARE FAILURE!

  • Limited to professional personnel for completely clearing/restoring the entire device.

  • Unless specifically required when flashing base firmware, do NOT check Erase All Before Download.

  • If it needs to be used due to special circumstances, immediately disable the clear option after use.

images/QC_Flash_17.png

Be careful not to check it by mistake

AI Translation Notice

This page was translated into English by AI and is provided for reference only. The original document is written in Chinese. If there is any discrepancy, the Chinese version prevails.

本页英文内容由 AI 自动翻译生成,仅供参考;原文为中文,如有差异请以中文原文为准。

查看中文原文 / View the Chinese original →