Interface Definitions

The DC695 provides a rich set of interfaces, as shown in the following diagram:
Overall Interface Diagram
Overall Device Interfaces
J1/J2 Power Supply
Pin Definitions
| Pin No. | Pin Description | Wire Color (Reference) | Notes |
|---|---|---|---|
| 1 | 12V | Red | Operating Voltage 12V |
| 2 | 12V | Red | Operating Voltage 12V |
| 3 | TX | White | RS232/UART TX |
| 4 | RX | Green | RS232/UART RX |
| 5 | GND | Black | Ground |
| 6 | GND | Black | Ground |
Connect to a 12V Power Supply
- Supports two power connectors:
DC 12V DC 55/25or6Pin PH2.0– chooseone .
Connection Method
Measured Power Consumption
-
Test Method:
- Flash the default
AndroidfirmwarePreliminary Evaluation Test Firmware - Power on normally, unlock the screen, and perform no other operations.
- Measure only the motherboard power; the backlight is not connected.
- Flash the default
| State | Voltage | Current | Power | Notes |
|---|---|---|---|---|
| Normal boot, no screen connected | 12.4V | 0.2A | 1.8-2.7W | Measurement accuracy 0.1 |
J3 Backlight Power Supply
| Pin No. | Pin Description | Wire Color (Reference) | Notes |
|---|---|---|---|
| 1 | 12V | Red | Operating Voltage 12V |
| 2 | 12V | Red | Operating Voltage 12V |
| 3 | BL EN | Yellow | Backlight Control |
| 4 | BL PWM | Yellow | Backlight Control |
| 5 | GND | Black | Ground |
| 6 | GND | Black | Ground |
- Maximum
3A Max
J4 MIPI Camera Interface
- Connector Model: YXT-BB10-30S-02
J5 TYPE-C Full-Featured Port
- Full-featured TYPE-C Port: Supports DP output and USB3.0 OTG function.
J5/J8/J9 USB Ports
- Supports 3x USB PH2.0 ports.
| Pin No. | Pin Description | Wire Color (Reference) | Notes |
|---|---|---|---|
| 1 | GND | Black | Ground |
| 2 | DP | Green | |
| 3 | DM | White | |
| 4 | 5V | Red | 5V |
J10 HDMI-IN Video Input
- 1x HDMI IN: Supports resolutions up to 19201080@60 / 38402160@30 -->
J11 3.5mm Headphone Jack
3.5mm Jack: American Standard (CTIA).
J12 Microphone Input
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | MIC1+ | Red |
| 2 | MIC1- | Black |
| 3 | MIC2+ | Red |
| 4 | MIC2- | Black |
J13 EDP Interface
- EDP interface.
J14 EDP Power Selection
- Pay attention to the
output voltage to avoiddamaging the screen .
J15/J16 Speaker / Audio Amplifier Output
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | RP | Red |
| 2 | RN | Black |
| 3 | LN | Black |
| 4 | LP | Red |
J17 WI-FI / BT ipex1 Generation Antenna Interface
- WI-FI / BT ipex1 generation antenna interface.
J18 SYS FAN (Cooling Fan)
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | 5V | Red |
| 2 | GND | Black |
J19 GPIO Interface
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | 3V3 | Red |
| 2 | GPIO B6 | Green |
| 3 | GPIO A5 | Green |
| 4 | GND | Black |
| 5 | GPIO C3 | Green |
| 6 | GPIO C2 | Green |
J20 RTC Battery
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | 3V3 | Red |
| 2 | GND | Black |
J21 UART/Debug Port
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | GND | Black |
| 2 | TX | Green |
| 3 | RX | White |
| 4 | 3V3 | Red |
J22 Panel Button Interface
| Pin No. | Pin Description | Wire Color (Reference) | Notes |
|---|---|---|---|
| 1 | Power Key | None | Short to 5 GND for power button |
| 2 | Reset | None | Short to 5 GND for reset button |
| 3 | Menu | None | Short to 5 GND for menu button |
| 4 | Volume - | None | Short to 5 GND for Volume - |
| 5 | GND | Black | Ground |
| 6 | Volume + | None | Short to 5 GND for Volume + |
- Press and hold
Volume + during startup to enter Loader upgrade mode .
J23 40PIN Expansion Interface
- Expansion supports USB, SD-Card.
J24 30PIN HDMI Expansion
S1 Boot/Upgrade Button
Press and hold to enter
Expansion Board and Interfaces
J1 Power Supply
- DC5525 12V
J2 12V DC OUT
- Outputs DC12V to the DC695-F motherboard.
J3 FPC 40PIN 0.5MM
- FPC 40PIN 0.5MM to DC695-F motherboard.
J4 USB Port
- Standard USB-A, maximum output 1A MAX.
J5 Headphone Jack
- American standard headphone jack.
J6 HDMI-IN
- Standard HDMI-IN input, supports hot-swap.
J7 FPC 30PIN 0.5MM
J8 TYPE-C Port
- Type-C Port: Supports OTG, Debug.
S1 Boot/Upgrade Button
Press and hold to enter
Overall Device Interfaces
Connection Method
























