Skip to main content

Interface Definitions

Navigation bar

The DC695 provides a rich set of interfaces, as shown in the following diagram:

Overall Interface Diagram​

Front Overall Device Interfaces

J1/J2 Power Supply​

Pin Definitions​

Pin No.Pin DescriptionWire Color (Reference)Notes
112VRedOperating Voltage 12V
212VRedOperating Voltage 12V
3TXWhiteRS232/UART TX
4RXGreenRS232/UART RX
5GNDBlackGround
6GNDBlackGround

Connect to a 12V Power Supply​

  • Supports two power connectors: DC 12V DC 55/25 or 6Pin PH2.0 – choose one.

Photo Connection Method

Measured Power Consumption​

  • Test Method:

    1. Flash the default Android firmware Preliminary Evaluation Test Firmware
    2. Power on normally, unlock the screen, and perform no other operations.
    3. Measure only the motherboard power; the backlight is not connected.
StateVoltageCurrentPowerNotes
Normal boot, no screen connected12.4V0.2A1.8-2.7WMeasurement accuracy 0.1 For reference only

J3 Backlight Power Supply​

Photo

Pin No.Pin DescriptionWire Color (Reference)Notes
112VRedOperating Voltage 12V
212VRedOperating Voltage 12V
3BL ENYellowBacklight Control
4BL PWMYellowBacklight Control
5GNDBlackGround
6GNDBlackGround
  • Maximum 3A Max

J4 MIPI Camera Interface​

Photo

  • Connector Model: YXT-BB10-30S-02

Photo

  • Full-featured TYPE-C Port: Supports DP output and USB3.0 OTG function.

J6/J7/J8/J9 USB Ports​

Photo

  • Supports 2x USB PH2.0 ports.
Pin No.Pin DescriptionWire Color (Reference)Notes
1GNDBlackGround
2DPGreen
3DMWhite
45VRed5V
  • Supports 2x USB-A ports.

Standard USB interfaces.

J10 HDMI-IN Video Input​

Photo

  • 1x HDMI IN: Supports resolutions up to 19201080@60 / 38402160@30.

J11 3.5mm Headphone Jack​

Photo

3.5mm Jack: American Standard (CTIA).

J12 Microphone Input​

Photo

Pin No.Pin DescriptionWire Color (Reference)
1MIC1+Red
2MIC1-Black
3MIC2+Red
4MIC2-Black

J13 EDP Interface​

Photo

  • EDP interface.

J14 EDP Power Selection​

Photo

  • Pay attention to the output voltage to avoid damaging the screen.

J15/J16 Speaker / Audio Amplifier Output​

Photo

Pin No.Pin DescriptionWire Color (Reference)
1RPRed
2RNBlack
3LNBlack
4LPRed

J17 WI-FI / BT ipex1 Generation Antenna Interface​

Photo

  • WI-FI / BT ipex1 generation antenna interface.

J18 SYS FAN (Cooling Fan)​

Photo

Pin No.Pin DescriptionWire Color (Reference)
15VRed
2GNDBlack

J19 GPIO Interface​

Photo

Pin No.Pin DescriptionWire Color (Reference)
13V3Red
2GPIO B6Green
3GPIO A5Green
4GNDBlack
5GPIO C3Green
6GPIO C2Green

J20 RTC Battery​

Photo

Pin No.Pin DescriptionWire Color (Reference)
13V3Red
2GNDBlack

J21 UART/Debug Port​

Photo

Pin No.Pin DescriptionWire Color (Reference)
1GNDBlack
2TXGreen
3RXWhite
43V3Red

J22 Panel Button Interface​

Photo

Pin No.Pin DescriptionWire Color (Reference)Notes
1Power KeyNoneShort to 5 GND for power button
2ResetNoneShort to 5 GND for reset button
3MenuNoneShort to 5 GND for menu button
4Volume -NoneShort to 5 GND for Volume -
5GNDBlackGround
6Volume +NoneShort to 5 GND for Volume +
  • Press and hold Volume + during startup to enter Loader upgrade mode.

S1 Boot/Upgrade Button​

Photo

Press and hold to enter Maskrom upgrade mode.

AI Translation Notice

This page was translated into English by AI and is provided for reference only. The original document is written in Chinese. If there is any discrepancy, the Chinese version prevails.

本页英文内容由 AI 自动翻译生成,仅供参考;原文为中文,如有差异请以中文原文为准。

查看中文原文 / View the Chinese original →