Skip to main content

Interface Definitions

Navigation bar

The DC686 provides a rich set of interfaces, as shown in the following diagram:

Overall Interface Diagram​

Front Overall Device Interfaces

J1 TYPE-C Port​

Photo

  • TYPE-C Port: Debug

J2/J3 Power Supply​

Photo Connection Method

Pin Definitions​

Pin No.Pin DescriptionWire Color (Reference)Notes
1GNDBlackGround
2GNDBlackGround
312VRedOperating Voltage 12V
412VRedOperating Voltage 12V

Connect to a 12V Power Supply​

  • Supports DC 12V 4PIN power connector

Measured Power Consumption​

  • Test Method:

    1. Flash the default Android firmware.

    2. Power on normally, unlock the screen, and perform no other operations.

    3. Measure only the motherboard power; the backlight is not connected.

StateVoltageCurrentPowerNotes
Normal boot, no screen connected12.4V0.2AStandby 2.3-3.1WMeasurement accuracy 0.1 For reference only

J4 Backlight Power Supply​

Photo

Pin No.Pin DescriptionWire Color (Reference)Notes
112VRedOperating Voltage 12V
212VRedOperating Voltage 12V
3BL ENYellowBacklight Control
4BL PWMYellowBacklight Control
5GNDBlackGround
6GNDBlackGround
  • Maximum 3A Max

J5 SPI​

Photo

Pin No.Pin DescriptionNotes
13V3
2SPI2_CLK_3
3SPI2_MOSI_3
4SPI2_MISO_3
5SPI2_CS_3
6GND

J6 I2C​

Photo

Pin No.Pin DescriptionNotes
13V3
2TP_SDA_3
3TP_SCL_3
4GND

J7 UART/Debug Port​

Photo

Pin No.Pin DescriptionWire Color (Reference)
1GNDBlack
2TXGreen
3RXWhite
43V3Red

J8 Panel Button Interface​

Photo

Pin No.Pin DescriptionWire Color (Reference)Notes
1Power KeyNoneShort to 5 GND for power button
2GPIO57_3v3None
3GPIO44_3V3None
4Volume -NoneShort to 5 GND for Volume -
5GNDBlackGround
6Volume +NoneShort to 5 GND for Volume +
  • Press and hold Volume + during startup to enter Loader upgrade mode.

J9 TF-Card Slot​

Photo

Max tested capacity 256GB, theoretically supports up to 512GB.

J10 MIPI Camera Interface​

Photo

  • Connector Model: YXT-BB10-30S-02

J11 HDMI-IN Video Input​

Photo

  • 1x HDMI IN: Supports resolutions up to 19201080@60 / 38402160@30.

J12 Ethernet Port​

Photo

  • Auto-negotiating Ethernet, supports 10/100Mbps.

  • J12 and J15 are outputs from the same USB HUB port, so J12 USB and J15 Ethernet port are mutually exclusive.

J13/J14 USB-A 3.0 Ports​

Photo

  • Supports 2x standard USB-A 3.0 ports.

J15 USB Port​

Photo

  • Supports 1x USB PH2.0 port.

  • J12 and J15 are outputs from the same USB HUB port, so J12 USB and J15 Ethernet port are mutually exclusive.

Pin No.Pin DescriptionWire Color (Reference)Notes
1GNDBlackGround
2DPGreen
3DMWhite
45VRed5V

J16 LVDS Power Selection​

Photo

  • Pay attention to the output voltage to avoid damaging the screen.

J17 LVDS Interface​

Photo

  • LVDS interface.

J18 3.5mm Headphone Jack​

Photo

3.5mm Jack: American Standard (CTIA).

J18 3.5mm Microphone Jack​

Photo

3.5mm Jack: Shared/parallel connection with MIC2.

J20 Speaker / Audio Amplifier Output​

Photo

Pin No.Pin DescriptionWire Color (Reference)
1RPRed
2RNBlack
3LNBlack
4LPRed

J21/J23/J25/J26 WI-FI / BT / 4G Antenna(s)​

Photo

  • Standard version only needs to connect the J23 WI-FI antenna.

J22 MIC 3.5mm Microphone Input​

Photo

  • American Standard interface.

J24 GPIO​

Photo

Pin No.Pin DescriptionNotes
1GPIO1243v3
2GPIO1233v3
3GPIO583v3
4GNDGround

J27 SIM Card Slot​

Photo

  • Only installed on versions with 4G module.

J28 SYS FAN (Cooling Fan)​

Photo

Pin No.Pin DescriptionWire Color (Reference)
15VRed
2GNDBlack

J29 RTC Battery​

Photo

Pin No.Pin DescriptionWire Color (Reference)
13V3Red
2GNDBlack

J32 Microphone Input​

Pin No.Pin DescriptionWire Color (Reference)
1MIC1_PRed
2MIC1_NBlack
3MIC2_PRed
4MIC2_NBlack

S1 DIP Switch​

Photo

  • Component Model: DSPV04LSGET, DIP Switch - Side-actuated Piano Key - SMT - 2.54mm pitch - 4 positions - DSPV04LSGET
Switch No.NameState (Up/Down)Corresponding FunctionNotes
1TAG_DATA_FORMATUp/PressedJEIDAAbnormal screen colors
2TAG_PORT_WASPUp/Pressed1Stripes appear on screen
3TAG_COLOR_DEPTHUp/PressedDEPTH_6BITColor difference on screen
4Backlight Polarity Adj.Up/PressedPolarity InversionBrightness decreases when trying to increase

Pressing the switch towards the PCB shorts the GPIO.

S2 Boot/Upgrade Button​

Photo

Press and hold during power-on/startup to enter Loader upgrade mode.

AI Translation Notice

This page was translated into English by AI and is provided for reference only. The original document is written in Chinese. If there is any discrepancy, the Chinese version prevails.

本页英文内容由 AI 自动翻译生成,仅供参考;原文为中文,如有差异请以中文原文为准。

查看中文原文 / View the Chinese original →