Interface Definitions

The DC665-E provides a rich set of interfaces, as shown in the following diagram:
Overall Interface Diagram
Overall Device Interfaces
J1 TYPE-C Multifunctional Port
- TYPE-C Port: Debug.
J2/J3 Power Supply
Connection Method
Pin Definitions
| Pin No. | Pin Description | Wire Color (Reference) | Notes |
|---|---|---|---|
| 1 | GND | Black | Ground |
| 2 | GND | Black | Ground |
| 3 | 12V | Red | Operating Voltage 12V |
| 4 | 12V | Red | Operating Voltage 12V |
Connect to a 12V Power Supply
- Supports
DC 12V 4PINpower connector
Measured Power Consumption
-
Test Method:
-
Flash the default
Androidfirmware. -
Power on normally, unlock the screen, and perform no other operations.
-
Measure only the motherboard power; the backlight is not connected.
-
| State | Voltage | Current | Power | Notes |
|---|---|---|---|---|
| Normal boot, no screen connected | 12.4V | 0.2A | Standby 2.3-3.1W | Measurement accuracy 0.1 |
J4 Backlight Power Supply
| Pin No. | Pin Description | Wire Color (Reference) | Notes |
|---|---|---|---|
| 1 | 12V | Red | Operating Voltage 12V |
| 2 | 12V | Red | Operating Voltage 12V |
| 3 | BL EN | Yellow | Backlight Control |
| 4 | BL PWM | Yellow | Backlight Control |
| 5 | GND | Black | Ground |
| 6 | GND | Black | Ground |
- Maximum
3A Max
J5/J15 USB Ports
-
Supports 2x USB PH2.0 ports.
-
J12 and J15 are outputs from the same USB HUB port, so
J12 USB and J15 Ethernet port are mutually exclusive .
| Pin No. | Pin Description | Wire Color (Reference) | Notes |
|---|---|---|---|
| 1 | GND | Black | Ground |
| 2 | DP | Green | |
| 3 | DM | White | |
| 4 | 5V | Red | 5V |
J6 I2C Port
| Pin No. | Pin Description | Notes |
|---|---|---|
| 1 | 3V3 | |
| 2 | SDA 3 | |
| 3 | SCL 3 | |
| 4 | INT | |
| 5 | RESET | |
| 6 | GND | Ground |
J7 UART/Debug Port
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | GND | Black |
| 2 | TX | Green |
| 3 | RX | White |
| 4 | 3V3 | Red |
J8 Panel Button Interface
| Pin No. | Pin Description | Wire Color (Reference) | Notes |
|---|---|---|---|
| 1 | Power Key | None | Short to 5 GND for power button |
| 2 | GPIO57_3v3 | None | |
| 3 | GPIO44_3V3 | None | |
| 4 | Volume - | None | Short to 5 GND for Volume - |
| 5 | GND | Black | Ground |
| 6 | Volume + | None | Short to 5 GND for Volume + |
- Press and hold
Volume + during startup to enter Loader upgrade mode .
J9 TF-Card Slot
Max tested capacity 256GB, theoretically supports up to 512GB.
J10 MIPI Camera Interface
- Connector Model: YXT-BB10-30S-02
J11 HDMI-OUT Video Output
- 1x HDMI OUT: Supports resolutions up to 19201080@60 / 38402160@30.
J12 Ethernet Port
-
Auto-negotiating Ethernet, supports 10/100Mbps.
-
J12 and J15 are outputs from the same USB HUB port, so
J12 USB and J15 Ethernet port are mutually exclusive .
J13/J14 USB-A 4-Pin Ports
- Supports 2x standard USB-A 2.0 ports.
J16 LVDS Power Selection
- Pay attention to the
output voltage to avoiddamaging the screen .
J17 LVDS Interface
- LVDS interface.
J18 3.5mm Headphone Jack
3.5mm Jack: American Standard (CTIA).
J18 3.5mm Microphone Jack
3.5mm Jack: Shared/parallel connection with MIC2.
J20 Speaker / Audio Amplifier Output
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | RP | Red |
| 2 | RN | Black |
| 3 | LN | Black |
| 4 | LP | Red |
J21/J23/J25/J26 WI-FI / BT / 4G Antenna(s)
- Standard version only needs to connect the J23 WI-FI antenna.
J22 MIC 3.5mm Microphone Input
- American Standard interface.
J24 GPIO
| Pin No. | Pin Description | Notes |
|---|---|---|
| 1 | GPIO124 | 3v3 |
| 2 | GPIO123 | 3v3 |
| 3 | GPIO58 | 3v3 |
| 4 | GND | Ground |
J27 SIM Card Slot
- Only installed on versions with 4G module.
J28 SYS FAN (Cooling Fan)
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | 5V | Red |
| 2 | GND | Black |
J29 RTC Battery
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | 3V3 | Red |
| 2 | GND | Black |
J32 Microphone Input
| Pin No. | Pin Description | Wire Color (Reference) |
|---|---|---|
| 1 | MIC1_P | Red |
| 2 | MIC1_N | Black |
| 3 | MIC2_P | Red |
| 4 | MIC2_N | Black |
S1 DIP Switch
- Component Model:
DSPV04LSGET, DIP Switch - Side-actuated Piano Key - SMT - 2.54mm pitch - 4 positions - DSPV04LSGET
Switch No. Name State (Up/Down) Corresponding Function Notes 1 TAG_DATA_FORMAT Up/Pressed JEIDA Abnormal screen colors 2 TAG_PORT_WASP Up/Pressed 1 Stripes appear on screen 3 TAG_COLOR_DEPTH Up/Pressed DEPTH_6BIT Color difference on screen 4 Backlight Polarity Adj. Up/Pressed Polarity Inversion Brightness decreases when trying to increase
Pressing the switch towards the PCB
S2 Boot/Upgrade Button
Press and hold during power-on/startup to enter
```markdown
> | Interface | Pin No. | Pin Description | Notes |
> |:---:|:---:|:---:|:---:|
> | S1 | 1,2,3,4 | GND | |
> | S1 | 5 | GPIO_33 | |
> | S1 | 6 | GPIO_95 | |
> | S1 | 7 | GPIO_93 | |
> | S1 | 8 | GPIO_92 | |
### J13 EDP Interface
> 
* EDP interface
### J14 EDP Power Selection
> 
* Pay attention to the <red class="red-soft">output voltage</red> to avoid <red class="red-soft">damaging the screen</red>.
### J17 Wi-Fi / BT ipex1 Generation Antenna Interface
> 
* Wi-Fi / BT ipex1 generation antenna interface
### J19 GPIO Interface
> 
| Pin No. | Pin Description | Wire Color (Reference) |
| :--- | :--- | :--- |
| 1 | 3V3 | Red |
| 2 | GPIO B6 | Green |
| 3 | GPIO A5 | Green |
| 4 | GND | Black |
| 5 | GPIO C3 | Green |
| 6 | GPIO C2 | Green |
### USB
> 
> USB Interface
### UART Description
The RV1126 default setting is I2C. To use TTL, you need to flash the <red class="red-soft">BOOT partition</red> separately. After flashing and upgrading, the interface becomes `ttyS0` with a default baud rate of `9600`.
> Link: https://pan.baidu.com/s/1NyfRuSKcakxMJCZohiFl6A?pwd=fanc Extraction code: fanc
| Pin No. | Pin Description |
| :--- | :--- |
| 1 | GND |
| 2 | GND |
| 22 | TX |
| 23 | RX |
> 
> **Connection Method**
#### 24-pin Expansion Interface Information:
> 24 PIN 0.5MM FPC Connector Model: X05C2024TZ
### RS-485 Description
The RS-485 interface is `ttyS3` with a default baud rate of `9600`.
| Pin No. | Pin Description |
| :--- | :--- |
| 1 | GND |
| 2 | A |
| 3 | B |
> 
> **Connection Method**
### Debug Description
Please use `TTL debug 1500000` (with five zeros).
| Pin No. | Pin Description |
| :--- | :--- |
| 1 | GND |
| 2 | TX |
| 3 | TX |
#### Usage

---
### MIPI Description
* 40PIN Dual MIPI/LVDS input interface (supports 4 lanes)
* Interface definitions are detailed in the specification.
* Default sensor options: `IMX415`, `IMX307`.
> 
> **Connection Method**
#### 40-pin MIPI Interface Information:
> 40 PIN 0.5MM FPC Connector Model: X05C2040TZ
### UART Description
The RV1126 default setting is I2C. To use TTL, you need to flash the <red class="red-soft">BOOT partition</red> separately. After flashing and upgrading, the interface becomes `ttyS0` with a default baud rate of `9600`.
> Link: https://pan.baidu.com/s/1NyfRuSKcakxMJCZohiFl6A?pwd=fanc Extraction code: fanc
| Pin No. | Pin Description |
| :--- | :--- |
| 1 | GND |
| 2 | GND |
| 22 | TX |
| 23 | RX |
> 
> **Connection Method**
#### 24-pin Expansion Interface Information:
> 24 PIN 0.5MM FPC Connector Model: X05C2024TZ
### Debug Description
Please use `TTL debug 1500000` (with five zeros).
| Pin No. | Pin Description |
| :--- | :--- |
| 1 | GND |
| 2 | TX |
| 3 | TX |
#### Usage

Overall Device Interfaces
Connection Method




















