Skip to main content

Upgrading the Firmware

Navigation bar

Preface​

This document describes how to flash the firmware from a host PC to the storage of the CAM126B-P development board via a data cable.

When upgrading, you need to choose the firmware according to your actual needs and select the appropriate upgrade method.

Obtaining the Firmware​

Note

CAM126 and CAM126B-P are different platforms. Apart from general instructions, their chips/firmware/software are not compatible with each other.

If flashing fails, please check the chip carefully:

CAM126 shows the following in the chip information: RV1126 CAM126B-P shows the following in the chip information: RK110F

Link: https://pan.baidu.com/s/1yGQ0tM284172IdOjHqJLEg?pwd=fanc Extraction code: fanc

CAM126B-P GC2093 dual-camera firmware​

Link: https://pan.baidu.com/s/1fuaQ2axrFvQZCCoJc7goIQ?pwd=fanc Extraction code: fanc

CAM126B-P Buildroot​

Rockchip-RV1126B-Buildroot

Link: https://pan.baidu.com/s/1CWHPvEa7Xcos_nBUkmv_1A?pwd=fanc Extraction code: fanc

CAM126B-P Debian12​

Rockchip-RV1126B-Debian12

Link: https://pan.baidu.com/s/1dT0vp3heGlfbbikHmVPeHg?pwd=fanc Extraction code: fanc

CAM126B-P Buildroot IPC​

Rockchip-RV1126B-Buildroot-IPC

Link: https://pan.baidu.com/s/1Vgon1tkSlNoQYPfyDDBYZg?pwd=fanc Extraction code: fanc

Installing the Flashing Tool​

Downloading the Materials​

Install the RK USB driver Release_DriverAssistant.zip

Run the RK flashing tool RKDevTool_Release_v3.32

Extracting​

  • Extract Release_DriverAssistant and RKDevTool_Release_v3.32

Photo Extract the tools

Installing the Driver​

  • So that all devices use the updated driver, please select driver uninstall first, and then select driver install.

Photo Install the driver

Running the Flashing Tool​

Photo Extract the archive and run RKDevTool.exe in the RKDevTool_Release_v3.32 directory (note: on Windows 7/8, right-click it and choose Run as administrator)

Entering Loader Mode​

There are two ways to enter Loader mode:

Entering Loader Mode via a Terminal Command​

Enter the command directly in the terminal:

  • After the adb terminal is up, you can enter reboot loader to enter it.

Photo Entering Loader mode

Entering Loader Mode via the BOOT Button​

Switch the upgrade mode with the boot button:

  1. Disconnect all power
  2. Press and hold the boot button
  3. Connect the USB data cable; the device will power on automatically and enter loader mode
  4. You can then release the BOOT button.

photo Hold the Boot button and then power on

Entering Maskrom Mode​

Entering Maskrom Mode via the Maskrom Button​

photo Hold the Maskrom button and then power on

  • You can short the two contacts shown in the figure with tweezers or another metal object

Starting the Upgrade​

Follow the steps below to upgrade CAM126B-P

Upgrade Steps​

  • 1-2 Extract the firmware
  • 3 Check and make sure it has entered Loader mode
  • 4 For the firmware, select the firmware extracted in step 1-2
  • 5 Click the upgrade button

Photo Starting the upgrade

Completing the Upgrade​

Wait for Download firmware 100% and Download firmware successful, which means the upgrade is complete.

Photo Upgrade complete

AI Translation Notice

This page was translated into English by AI and is provided for reference only. The original document is written in Chinese. If there is any discrepancy, the Chinese version prevails.

本页英文内容由 AI 自动翻译生成,仅供参考;原文为中文,如有差异请以中文原文为准。

查看中文原文 / View the Chinese original →