Skip to main content

Interface Description

Navigation bar

The module uses an LCC + LGA 447-pin package. The table below lists the interface resources available on the module; for detailed pin definitions, refer to the "DL562 Pin Assignment and Pin Description".

Interface Resources​

InterfaceQuantity / CapabilityNotes
RGMII1 groupExternal gigabit PHY for a single gigabit Ethernet port
RMIIUp to 2 groupsExternal 100M PHY; can be combined with RGMII
USB1 × USB3.0 OTG + 1 × USB2.0 HOSTUSB0 is used for firmware upgrade and is multiplexed with PCIe
PCIe1 × Gen2 1-laneRC mode only
DisplayMIPI DSI 1.2 / LVDS / RGB / BT.656 / BT.1120Dual-display simultaneous output supported
Camera2 × 4-lane MIPI CSI (splittable into 4 × 2-lane) / DVPUp to 13 MP
SD card1 × SD 3.0—
SDIOUp to 2 groupsCommonly used for external Wi-Fi
UARTUp to 10 groupsUp to 4 Mbps; debug UART uses 1.8 V levels
I2CUp to 5 groupsMaster mode only, 1.8 V levels, up to 400 kbps
SPIUp to 3 groupsMaster / slave modes
I2SUp to 3 groupsDigital audio
PDMUp to 4 channelsUp to 192 kHz
CANUp to 2 groupsCAN0 is in the 3.3 V domain, CAN1 in the 1.8 V domain
ADC13 channelsGeneral-purpose ADC
PWMUp to 16 channels—
GPIOUp to 86 pinsSee pin description for multiplexed functions
WirelessNo onboard wirelessExternal Wi-Fi / Bluetooth via SDIO + UART

Carrier Board Design Notes​

DL562 is an LGA SMT module and cannot be used standalone; a carrier board must be designed and SMT assembled. Pay attention to the following when designing the carrier board:

  • Power: VBAT supply is 3.3 ~ 3.5 V (typical 3.4 V), with peak current up to about 3 A. Place a 100 μF low-ESR capacitor plus 22 μF, 100 nF and 33 pF filter capacitors close to the VBAT pins, and keep the VBAT trace width at least 2 mm.
  • Power on / off: pull PWRKEY low for 0.5 ~ 6 s to power on, and for more than 6 s to power off; pull RESET_N low for more than 100 ms to restart; PON_1 rising edge can also be used to power on.
  • Firmware upgrade: upgrade over USB0 (OTG); route USB0 to a pluggable connector on the carrier board. VOL_UP/BOOT (active low) enters Loader mode, and pulling EDL low enters Maskrom mode. Reserve test points for both.
  • Debug UART: DBG_TXD / DBG_RXD, default baud rate 115200, 1.8 V levels; level shifting is required when connecting to 3.3 V systems.
  • Ethernet: the module only exposes RGMII / RMII; external gigabit or 100M PHYs are required for Ethernet ports.
  • Wireless (external option): use SDIO for Wi-Fi and UART for Bluetooth, and reserve control signals such as WIFI_REG_ON, WIFI_WAKE_HOST and BT_REG_ON. Antennas require 50 Ω impedance control; refer to the "Fanconn Antenna Design Guide".
  • I2C / CAN levels: I2C is 1.8 V open-drain and requires external pull-ups; CAN0 is in the 3.3 V domain and CAN1 in the 1.8 V domain, so match the transceiver levels accordingly.
  • Mechanical: a shield cover and heatsink are supported; refer to the 2D / 3D drawings for height and cutout details.
AI Translation Notice

This page was translated into English by AI and is provided for reference only. The original document is written in Chinese. If there is any discrepancy, the Chinese version prevails.

本页英文内容由 AI 自动翻译生成,仅供参考;原文为中文,如有差异请以中文原文为准。

查看中文原文 / View the Chinese original →